AcuraZine - Acura Enthusiast Community

AcuraZine - Acura Enthusiast Community (https://acurazine.com/forums/)
-   2G CL (2001-2003) (https://acurazine.com/forums/2g-cl-2001-2003-50/)
-   -   Small oil leak around oil pressure sensor - help (https://acurazine.com/forums/2g-cl-2001-2003-50/small-oil-leak-around-oil-pressure-sensor-help-847123/)

01RedCLS 02-10-2012 10:05 AM

Small oil leak around oil pressure sensor - help
 
I took my CL-S in for an oil change (Mobil 1 Syn) and tire rotation yesterday and in the "Comments" section of the "Acura Multi-Point Vehicle Inspection Checklist", the tech noted:

"has a small oil leak around oil pressure sensor"

First of all, where is the oil pressure sensor? And what could be causing the leak - any common problems in/around this area that you know of?

civicdrivr 02-10-2012 11:16 AM

The sensor is #17, located on the oil filter housing. Theres an o-ring on it:

http://www.acuraoemparts.com/delray/...3s3m01_e13.png

#29, part number 91319-PR3-003, lists for $2.50. Isn't difficult to install but you may get some oil leaking out when you pull out the sensor. Its possible its the o-ring from the solenoid (#15) too.

01RedCLS 02-10-2012 11:21 AM

Perfect, thank you! Is this relatively easy to get to and replace both o-rings on my own, I hope?? I know my way around my Miata and Focus (ZETEC) engine but the CL has been such an easy car to maintain, I am not as familiar under the hood ;).

TLer trash 02-10-2012 11:27 AM

#16 is the oil pressure sensor, #17 is the vtec oil pressure sensor. There are no o-rings on 16, it's tapered pipe thread. Fairly common source of oil leakage,

civicdrivr 02-10-2012 11:32 AM


Originally Posted by TLer trash (Post 13544567)
#16 is the oil pressure sensor, #17 is the vtec oil pressure sensor. There are no o-rings on 16, it's tapered pipe thread. Fairly common source of oil leakage,

Gah, youre right.

01RedCLS 02-10-2012 11:50 AM


Originally Posted by TLer trash (Post 13544567)
#16 is the oil pressure sensor, #17 is the vtec oil pressure sensor. There are no o-rings on 16, it's tapered pipe thread. Fairly common source of oil leakage,

So I just need to replace #16 then due to the oil leak?

dfv3.2CL-S 02-10-2012 03:15 PM

Most likely the oring is bad

01RedCLS 02-10-2012 03:17 PM

TLer Trash just said that #16 is a threaded pipe - no-oring...

StreetKA 02-10-2012 04:11 PM

if its expensive i may have one for you lmk.

01RedCLS 02-10-2012 05:18 PM


Originally Posted by StreetKA (Post 13545325)
if its expensive i may have one for you lmk.

StreetKA - PM'd you..

'01AcuraCL 09-16-2014 01:47 PM

oil pressure sensor
 
[IMG] I'm trying to find where the oil pressure sensor is located. I installed a new variable valve timing switch (#17 on the drawing) and from what I can see, it appears the oil pressure sensor is just inches away. Is it covered by a black plastic/rubber Hershey"s Kiss shaped cover? If so, does it just come off by pulling it or does it unscrew? Do I need to drain the oil prior to removing the oil pressure sensor? Thanks

TLer trash 09-16-2014 01:57 PM

^^Yes, the oil pressure sender has a boot over it. Peel the boot back (sometimes they're stiff, and will crack). The wire terminal is a spade type; it pulls straight off. You don't have to drain the oil.

'01AcuraCL 09-16-2014 02:33 PM

You're awesome!

YeuEmMaiMai 09-17-2014 03:02 PM

I had to do mine last year it was only $100 for the dealer to do it.


All times are GMT -5. The time now is 05:18 PM.


© 2024 MH Sub I, LLC dba Internet Brands